Clean up of debug prints, and safer CAS handling

ECU.ino

@@ -2,6 +2,7 @@
 #include "data.h"
 #include "schedule.h"
 #include "tables.h"
+void(* resetFunc) (void) = 0; //declare reset function @ address 0
 
 void setup() {
   // Sensors
@@ -45,4 +46,3 @@ void loop() {
   // Run scheduler
   schedule_process();
 }
-

battery.ino

@@ -12,10 +12,6 @@ void battery_init()
   {
     Serial.println("ERR: Battery high");
   }
-  else
-  {
-    Serial.println("INF: Battery ok");
-  }
 }
 
 void task_battery_run()
@@ -27,5 +23,3 @@ void task_battery_run()
   // Nudge it along so we have an index starting at 0 for tables etc
   battery_voltage_index = constrain(battery_voltage_value,7,16) - 7;
 }
-
-

cas.ino

@@ -56,7 +56,13 @@ void cas_process()
         else
         {
           // Clear it if we're in sync, but don't clear log flag
-          cas_sync_fail = 0;
+          if(cas_sync_initial == 1)
+          {
+              cas_sync_initial = 0;
+              cas_sync_fail = 0;
+              cas_sync_fail_log = 0;
+          }
+
         }
 
         // Use this number because we KNOW it's right
@@ -137,7 +143,3 @@ void cas_process()
   }
   cas_sgc_lastvalue = sgc;
 }
-
-
-
-

data.h

@@ -24,6 +24,7 @@ unsigned long   cas_sgc_lastrise          = 0;            // micros() of the las
 unsigned long   cas_sgc_lastfall          = 0;            //    ""    of the last fall
 byte            cas_sgc_lastvalue         = 0;            // The state of SGC on the previous cycle
 
+byte            cas_sync_initial          = 1;
 byte            cas_sync_fail             = 0;            // We lost track of a cylinder
 byte            cas_sync_fail_log         = 0;            // We need to output this in debug
 
@@ -57,4 +58,3 @@ byte            throttle_current_value    = 0;            // Percentage
 byte            throttle_previous_1_value = 0;            // Percentage
 byte            throttle_previous_2_value = 0;            // Percentage
 byte            throttle_delta            = 0;            // Difference between current and delta
-

debug.ino

@@ -18,7 +18,10 @@ void task_debug_run()
   // Log if we're out of sync timing-wise
   if(cas_sync_fail_log > 0)
   {
-    Serial.println("ERR: CAS sync fail");
+    if(cas_sync_initial == 0)
+    {
+       Serial.println("ERR: CAS sync fail");
+    }
     cas_sync_fail_log = 0;
   }
 
@@ -138,8 +141,14 @@ void task_debug_run()
     }else if(readbyte == 'R') // Enable RPM output
     {
       debug_rpm = 1;
+    }else if(readbyte == 'S') // Arduino reset
+    {
+      resetFunc();
     }
   }
+
+  // Allow it to re-sync (i.e. reset CAS failure as it was intentional)
+  cas_sync_initial = 1;
 }
 
 // Outputs the fuel table as JSON
@@ -200,4 +209,3 @@ void task_debug_safekill()
   cas_sync_fail=1;
   cas_sync_fail_log=0;
 }
-

map.ino

@@ -7,8 +7,6 @@ void map_init()
     Serial.println("ERR: MAP low");
   else if(map_current_value > 108)
     Serial.println("ERR: MAP high ");
-  else
-    Serial.println("INF: MAP ok");
 }
 
 void task_map_run()
@@ -17,5 +15,3 @@ void task_map_run()
   map_current_index = map(map_current_value, map_range_min, map_range_max, 0, 15);
   map_current_index = constrain(map_current_index,0,15);
 }
-
-